亚洲AV 日韩AV 无码

  • <td id="ihhf5"></td>
  • <acronym id="ihhf5"><strong id="ihhf5"></strong></acronym>

    <p id="ihhf5"></p>
  • 全國服務熱線:

    18396804865 錢經理

    數控切割機切割板才品質優劣

    2020-08-15 15:25:47文章來源:www.aaa-collectables.com621

    便攜式數控切割機激光切割板才出去的品質優劣有各個方面緣故,其關鍵緣故有以下內容1、板才放置不穩定.必需時能夠把板才加墊.

    The quality of laser cutting board of portable NC cutting machine is good or bad because of various reasons. The key reasons are as follows: 1. The board is not stable until it is placed. It can be padded only when necessary.

    2、割縫余量預留不足.尤其切割厚板時割縫余量至少在10mm以上.

    2. The slot allowance is insufficient. Especially when cutting thick plates, the slot allowance is at least 10 mm.

    3、工作環境光線不足.視覺觀察不準確.尤其是陰天、晚上作業.

    3. Insufficient light in the working environment, inaccurate visual observation, especially overcast and evening work.

    4、切割中熄弧或未割穿,此時對與厚板一定重新移至切割點以上2MM處再繼續切割,若未移至準確位置即起弧可能會對零件邊緣進一步融割出現缺陷.

    4. Extinguishing arc or not cutting in cutting. At this time, the thick plate must be moved to 2MM above the cutting point to continue cutting. If not moved to the exact position, arcing may cause defects in further cutting the edge of the part.

    5、切割行進方向應確保切割結束在大面積板區.若結束在小面積板區會因受熱板材移動導致切割變形.為此在切割厚板時可以正反方向各切割一段,相交處要及時熄火,避免切割過度致使零件缺損.

    5. Cutting direction should ensure that the end of cutting is in large area. If the end is in small area, the cutting deformation will be caused by the movement of heated plate. For this reason, when cutting thick plate, the cutting section can be cut in both positive and negative directions, and the intersection should be extinguished in time to avoid excessive cutting resulting in part defects.

    6、噴嘴,電極,噴嘴帽堅持每天檢查,如有損壞及時更換.

    6. Inspect nozzles, electrodes and nozzle caps every day and replace them in time if they are damaged.

    7、劃線要準確,留足割縫余量和板材邊緣余量.

    7. Marking should be accurate, leaving enough slot allowance and plate edge allowance.

    8、厚板切割需加工的余量放到10MM-15MM.

    8. The allowance for thick plate cutting should be placed at 10MM-15MM.

    9、劃線切割時板材擺放方向要結合零件排布、-X軸向切割來確定,力求便于觀察.

    9. The orientation of plate placement should be determined by combining the layout of parts and - X axial cutting, so as to facilitate observation.

    10、造成切割尺寸誤差的因素:對角線不準確、切割面傾斜、零件受熱移動、一處多次重復起弧、劃線不準確、起點、零點觀察不準確等.

    10. The factors causing the error of cutting dimension are inaccurate diagonal line, inclined cutting surface, parts moving by heat, repeated arcing in one place, inaccurate marking, inaccurate starting point, inaccurate zero observation, etc.

    正確使用操作數控切割機能有效提高切割質量以及減少板材的浪費

    Correct use of CNC cutting machine can effectively improve cutting quality and reduce waste of sheet metal http://www.aaa-collectables.com/

      報錯


      濟南卓然天成是大型數控火焰切割機廠家,數控等離子切割機廠家,便攜式數控切割機廠家www.aaa-collectables.com,供應河北數控火焰切割機,山西數控等離子切割機,遼寧便攜式數控切割機,吉林數控火焰切割機,黑龍江數控等離子切割機,江蘇數控切割機,浙江數控切割機,安徽數控切割機,福建切割機,江西切割機,山東數控切割機,臺灣切割機,河南切割機,湖北數控切割機,湖南數控切割機,廣東切割機,海南數控切割機,四川數控切割機,貴州數控切割機,云南切割機,陜西切割機,甘肅數控切割機,青海數控切割機,需要的朋友聯系我們15254176866

    電話咨詢
    郵件咨詢
    在線地圖
    QQ客服
    網站地圖 亚洲AV 日韩AV 无码
  • <td id="ihhf5"></td>
  • <acronym id="ihhf5"><strong id="ihhf5"></strong></acronym>

    <p id="ihhf5"></p>